DNC 連線軟體 CNC機台 連線軟體 下載 真正免費 免費 DNC 傳輸軟體 NC 編輯軟體 真正免費 @@@@

 

DNC 連線軟體 CNC機台 連線軟體 下載 真正免費 免費 DNC  傳輸軟體  NC 編輯軟體  真正免費

DNC 連線軟體 CNC機台 連線軟體 下載 真正免費 免費 DNC  傳輸軟體

Cnc dnc 連線 傳輸 SIEMENS POST  FANUC POST  後處理 Heidenhain 530i.PST Okuma OSP 5020.PST 後製處理 Mill LATHE Machine   Haas  Control 4-axis 5-axis

DNC 軟體下載處 (需登載):
http://www.onecnc.com/support/downloads/nclink-registration
http://onecnc.net/en/support/downloads/nclink-registration

DNC 軟體下載處 :(中文 )
http://onecnc.net/zh_tw/support/downloads/nclink-registration
登載後 約20分鐘, 您mail 收到下載指令

大家放心登載, 表示大方使用, 誰怕誰 ,您說對不對。
現今 軟體 哪一家沒有間諜偵蒐,您最好千萬不要用盜版軟體
你上網又使用盜版軟體, 真活該, 你在何處用, 幾點鐘用, 他人都在看
24 H 的

DNC 連線軟體 CNC機台 連線軟體 下載 真正免費

免費 DNC  傳輸軟體  NC 編輯軟體  真正免費

安裝後請參閱 HELP檔:有關參數設定
3條線之連接法 屬於 軟體交握

Fanuc 0 Series Controls Suggested Cable Pin Out

CNC Control	Computer 25 Pin	Computer 9 Pin
I/O Port	RS232 Port	RS232
DB-25 Male	DB-25 Male	DB-9 Male
1 (Chassis ground)	(Not connected)	(Not connected)
2	3	2
3	2	3
7	7	5
4 and 5 jumpered
6 8 20 jumpered

Notes on Suggested Machine Control Settings

1.	Set the PWE parameter to off. The machine will go into Alarm mode as you are setting the parameters. After done setting the parameters set PWE back on and hit Reset.
2.	Above procedure unnecessary to change Handy Page settings
3.	On 0 Series Controls using ISO format, only Baud rate and # of stop bits can be set. Always use Even parity, Word length 7, and 2 Stop bits.
4.	All Parameters set by 8 bit numbers are read right to left, e.g. Bit 0 is the rightmost bit and Bit 7 is the leftmost bit.
5.	Control must have tape reader to do direct DNC. To direct DNC, go to tape mode, set up OneCNC to Send and Wait for XON, hit Cycle Start at the CNC. To pause direct DNC turn Feedrate Override to 0%.

Suggested Machine Control Control Parameters

#0002	- Set Bit 0 to 1 for 2 Stop Bits-I/O = 0 Set Bit 2 to 0 for RS-232 Input
#552	= 10 (4800 Baud)

Suggested Machine Control Set Page Settings

 

    

I/O	= 0
ISO	Format

Suggested OneCNC Communication Send Settings

 

Baud Rate	4800 (Suggested starting point)
Parity	Even
Data Bits	7
Stop Bits	2
Handshake	Software - XON - XOFF
Start at Machine	Tagged active
First Lines	%
Last Lines	%
Remove Spaces	Tagged active

Suggested OneCNC Communication Settings for Receive

 

Baud Rate	4800 (Suggested starting point)
Parity	Even
Data Bits	7
Stop Bits	2
Handshake	Software - XON - XOFF
Receive Timeout	10000
Strip at end of Line

The settings are automatically saved when exiting the settings and they are saved to the currently loaded machine configuration. The Receive and Send settings are separately saved.